CBM Electronic thermometer & kit

DIGITAL THERMOMETER INSTRUCTION MANUAL THERMONETER | WK Gg Hl i | ||_28 | Unit and Sign Display : « Decimal point *F: Fahrenheit temperature scaie C : Celsius temperature scale : Low Battery — : Negative polarity [HOLD] : Data hold MAX : Max hold Over Range Indication : "OL" appears on the display. Low Battery Indication: The Luk is displayed when the battery voltage drops below the operating voltage. Display Rate : Approximately 2.5 times per second. Power Requirement : 9-Volt battery , NEDA 1604 or JIS OO6P or IECBF22 Battery Life ( typical ): 200hours ( Alkaline Batiery ) Dimensions: 135 (L) x 72(W) x 31(H)mm 5.3 (L) x 2.8(W) x 1.2(H)inches Weight: Approx. 235g with battery Accessories: Battery, Instruction Manual. Holster ( option } I. INTRODUCTION : This instrument is a digital thermometer’ for use with any k-type thermocouple as temperature sensor. Temperature indication follows National Bureau of Standards and 1EC584 temperature / voltage tables for K-type thermocouples. I. SPECIFICATIONS ; 2-1 Electrical Specifications Measurement Range : -50°C to 1300°C /-50°F to 1999°F Resolution: 0.1°C ,1C ,0:0F ,1°F Maximum Voltage at Thermocouple Input :60V de jor 24Vrms-ac RF Field Derating :Strong RF fields and low-frequency adversely affect accurate measurement . Environmental : Operating Temperature and Humidity: OC to 50°C (32°F to 122°F ) 40 - 8096RH Storage Temperature and Humidity: 10°C to60C (14°F to 140°F ) 10 - 709%6RH Basic Accuracy: {@23+ 5°C Calibration ) Accuracy aret (...% of reading + ..degree ) at 18°C to 28°C with relative humidity up to 80% 1 | | UL NAME OF PARTS AND POSITIONS <> see im 8 a For single thermocouple measurements Function .| Resolution Range Accuracy | Output Signal O17 | 50°C ~199.9 [z (0.3% +1C) [F (0.3964+2mv) 50C~1000C [+ (0.596+1C) | 1001°C ~1300% J+ (0.75% +1'C) -50F~| 0.1°F |-50°F~199.9°F |£ (0.396+2°F) | (0.596+5mv) 1999F | 1F | -S0°F~1999°F [+ (0.596+2°F) [# (0.75% +0.5mV) 50°C ~ 1300°C 1C c jt (0.75% +0.2mv) NOTE The basic accuracy specification does not include the error of the probe. please refer to the probe accuracy specification for additional details. Temperature Coefficient: For ambient temperatures from 0°C to 18°C and 28°C to 50° (32°F to 64°F and 82°F to 122°F ) Foreach ( °F ) ambient below 18°C (64°F ) or above 28°C ( 82°F ), add to the accuracy specifications: 0.01% of reading + 0.03°C (0.01% of réading + 0.06°F ) 2-2 General Specifications Numerical Display : 3 1/2 digital liquid crystal display (LCD ) 44mm height. maximum reading 1999. 2 @ LCD Display: 3.1/2 digits with a maximum reading of 1999, and indications or minus sign “—”, Data hold } » MAX HOLD “MAX”. “71”, “T2", “T1- T2”, F”, low battery etc. @ ON/OFF Switch: The ON/OFF Key tums the thermometer on or off. @ MAX HOLD Button : A Push Button (Push on/push off, push on :LCD appear MAX sign) @ HOLD: Pressing the HOLD key selects DATA HOLD mode. and "HOLD " symbol appears on the display. Pressing the HOLD key again cancels HOLD mode, and causes the thermometer to resume taking measurements. © Thermocoupie Input Connector. © 0.1" :Pressing the 0.1 key selects 0.1 degree resolution. Range from > to 199.9°C: or.-50°F to 199.9°F 7° cPressing the 1’ key selects 1 degree resolution Range from -50.0°C to. 1300°C or -50'F to 1999°F @ Fc. The FC key switches between the Celsius (‘C) and Fahrenheit (F)'scales on the display. T: The OFFSET controls allow you adjust offset value io optimize measurement accuracy for a particular ihermecouple at a particular. The OFFSET Controls are adjusted using a small screwdriver. 5 --- PAGE BREAK --- SD OUTPUTS: OUTPUTS from standard 3 pole 3.5ram Coaxial socket with DC+ on pin, and intermediate. {Internal Connector Pin and intermediate }, Ground on Sleeve. [Fig2} AmVde/ C CF). at 01 /0.1F resolution. OQimVde/ °C (CF). wat 1C/ 14°F. resolution. Output Impedance 502 DB Tilt stand GROUND DC+ OUTPUT [Fig 2} 6 TP-K01: Available for general condition, especially for complex and any piace hard to reach. TP-KO3: Available for flat or curved surface measurement. = = \ IVY. TEMPERATURE MEASUREMENT | 1. Turn on the thermometer. 2. Plug the thermocouple inte the thermocouple input connector. 3. Set the thermometer to desired function ¢ C or F scate & 0.1" or 1 resolution ) 4, Perform measurements by contacting the object being measured with the probe sensor. 5. Read the temperature on the display. WARNING Toavoid electrical shock,do not use this instrument when voltages exceeding 24V AC or 60V DC are present. The probe tip is electrically connected to the output terminals. Vv. ERROR INDICATION The “OL" is display if any of the following conditions occurs: 1. lf no thermocouple is plugged into the thermocouple input connector. 2. If the thermocouple connected to the input is broken or open circuited. [VL RECALIBRATION PROCEDURE: | The thermometer should be calibrated once a year fo ensure its accuracy is within specifications. The required equipmentis listed below : D0.0C: adjust VR1 @00F adjust VR2 @165.0F adjust VRS @ 952°F adjust VR4 @ 511°C adjust VR3 © OUTPUTS 0.0mVBC adjust VR7 (at 0:0°C) VIL OPTIONAL ACCESSORY K {CA ) type thermocouple. [ Model [Range [Tolerances [Description | ith Tefion tape insulation. laximum insulating 60T