51.0401.09 InterpumpGroup W1210 / Pistone D. 18x25 Buyer's Guide: Piston, Plunger & Pump Selection for Worldwide Buyers
Table of Contentsexpand_more
The 51.0401.09 InterpumpGroup W1210 / Pistone D. 18x25 is a replacement piston (Italian: pistone) measuring 18 mm diameter x 25 mm length, used in Interpump W-series high-pressure plunger pumps. It is a wear part: when a pump loses pressure, pulses, or leaks past the seals, the piston and its seal kit are the first items to inspect.
What is a 51.0401.09 InterpumpGroup W1210 piston?
A 51.0401.09 InterpumpGroup W1210 piston is a precision-ground plunger that reciprocates inside the pump manifold, displacing water at high pressure. Interpump — the Italian OEM behind the W, T and TX series — specifies piston diameter in millimetres, so "D. 18x25" means 18 mm diameter, 25 mm length.
Piston diameter directly sets the pump's flow-to-pressure balance. A larger piston moves more water per stroke (higher L/min) at a given rpm; a smaller piston reaches higher pressure for the same motor input. That is why Interpump offers the same crankcase with different piston bores.
How does an Interpump W-series piston work?
The piston is driven by the crankshaft through a connecting rod, drawing water through the inlet valve on the downstroke and forcing it through the outlet valve on the upstroke. Pressure is contained by a low-pressure seal and a high-pressure seal around the piston.
Because the piston contacts water and seals continuously, it is a consumable. Typical replacement intervals depend on water quality, duty cycle and inlet conditions — abrasive or hot water shortens life significantly.
Interpump W1210 piston and pump specifications
The table below summarises the published technical data for the W1210-class pump platform. Use it to confirm your pump matches before ordering the 51.0401.09 piston.
| Parameter | Value | Notes |
|---|---|---|
| Piston diameter x length | 18 mm x 25 mm | "Pistone D. 18x25" |
| Flow rate | 15 L/min (3.96 US gpm) | At rated rpm |
| Rotation regime | 1,750 rpm | 50 Hz nominal |
| Pressure | 200 bar (20 MPa / 2,900 psi) | Maximum continuous |
| Power | 5.73 kW (7.8 hp) | Absorbed at rated point |
| Overall dimensions | 273.5 mm x 223 mm x 152.5 mm | L x W x H |
| Weight | 9.5 kg | Pump assembly |
Note the shaft configuration: the datasheet for this platform lists a male shaft with key and plugs as out of production. If your pump uses that shaft, confirm the replacement pump or piston variant with 3G Electric before ordering.
Which Interpump pump or spare do you actually need?
Buyers searching "51.0401.09" usually fall into one of three groups: (1) replacing a worn piston in an existing W1210 pump, (2) replacing the whole pump because the crankcase or manifold is damaged, or (3) building a new high-pressure system and comparing Interpump models.
For group 1, the piston alone is rarely enough — order the matching seal kit at the same time. For group 2, step up to a complete pump with a known flow/pressure rating. For group 3, use the ladder below to compare Interpump models across the range.
Interpump product selection ladder
The table compares representative Interpump pumps and accessories from 3G Electric's stock, arranged from compact/light-duty through to high-power industrial duty.
| Model | Flow | Pressure | Power | Typical duty |
|---|---|---|---|---|
| Inter[[PRODUCT:TS1331-000|pump TS1331 | 13 L/min | 120 bar | 2.94 kW at 1,450 rpm | Light-duty washdown, compact skids |
| Inter[[PRODUCT:T01321-000|pump T1321 | 15 L/min class | 200 bar class | 5.73 kW class | General industrial cleaning |
| Inter[[PRODUCT:T09281S0U-000|pump T9281 L | Mid-range | High-pressure class | Mid-range | Continuous industrial duty |
| Interpump T2830Y SX Pump with 53R Motor | 30 L/min (7.92 US gpm) | 275 bar | 15.44 kW (21 hp) at 1,750 rpm | Heavy-duty, 18.5 kg assembly |
| Inter[[PRODUCT:AB0150CD-000|pump AB150 PTO R | PTO-driven | Agricultural class | PTO input | Agriculture / tractor-driven |
Step up the ladder when your duty cycle moves from intermittent washdown to continuous operation, or when you need more flow at the same pressure. Step down when portability, low absorbed power or a compact footprint matters more than maximum pressure.
Selection criteria: how to choose the right Interpump piston or pump
- Confirm piston diameter. Measure the old piston or read the pump plate. An 18 mm piston will not fit a manifold bored for 20 mm or 22 mm.
- Match flow and pressure to the application. 15 L/min at 200 bar suits general industrial cleaning; 30 L/min at 275 bar suits heavier duty.
- Check rpm and frequency. Interpump ratings are typically quoted at 1,750 rpm (50 Hz). At 60 Hz the same pump runs faster, so verify the motor and pulley ratio.
- Assess water quality and temperature. Abrasive or hot water accelerates piston and seal wear — plan a shorter service interval.
- Order the seal kit with the piston. Replacing a piston without new seals usually leads to a repeat failure.
- Verify shaft and coupling. Use the correct coupling — for example Interpump Flexible Coupling 56C — to avoid misalignment damage.
Types and applications in Worldwide markets
Interpump W- and T-series pumps are used worldwide in vehicle wash systems, food-plant washdown, pressure testing, descaling, hydro-excavation and agricultural spraying. In export markets, buyers typically specify 50 Hz or 60 Hz motor variants, and 3G Electric supplies both configurations with export documentation.
Accessories matter too: foam kits such as Interpump FOAMKIT 3 for T/TX Series and nozzle kits such as Interpump VarioJet Kit with 125 Nozzle complete a washdown system and are commonly ordered alongside pumps and spares.
Why source Interpump pumps and spares from 3G Electric
3G Electric stocks 4,007 products across 14 industrial departments — machining, electrical, power transmission, material handling, plumbing, HVAC & refrigeration, pneumatics, hydraulics, pumps, instrumentation, test & measurement, welding, lighting and combustion. Our specialist depth in pumps, combustion and controls means we interpret your demand and deliver the right part, not just a part number.
With 35+ years of experience, we support Worldwide buyers with technical sizing assistance, export documentation, incoterms-neutral supply and cross-market voltage/frequency variants. We are a distributor and supplier — not an authorised dealer — and we are accountable for every item we ship.
Key takeaways
- The 51.0401.09 InterpumpGroup W1210 / Pistone D. 18x25 is an 18 mm x 25 mm piston for Interpump W-series high-pressure pumps.
- W1210-class pumps typically deliver 15 L/min at 200 bar (20 MPa / 2,900 psi) and 1,750 rpm, absorbing 5.73 kW (7.8 hp).
- Always replace the piston together with its seal kit, and verify shaft/coupling compatibility.
- For 60 Hz markets, confirm motor speed and pulley ratio — the same pump runs faster at 60 Hz.
- 3G Electric supplies Interpump pumps, spares and accessories worldwide with technical support and export documentation.
Contact 3G Electric for a quote on the 51.0401.09 piston, a complete Interpump W1210 pump, or sizing assistance for your application. Send us your pump plate details and we will confirm the correct part.
