Datasheet Content
Digital Electronic Torque Wrench
Operating Manual
Model 60648
This manual will help you to use the many MAINTENANCE AND STORAGE
features of your new digital torque wrench.
Before operating the torque wrench, please read ATTENTION:
this manual completely, and keep it nearby for To maintain accuracy, a one-year
future reference. periodic recalibration is recommended.
Please contact your local dealer for
calibration details.
FEATURES
CAUTION:
1. Over-torque (110% of
● Interchangeable head
Max. torque range)
● Digital torque value readout could cause breakage
● +/- 2% accuracy or loss of accuracy.
● CW and CCW operation 2. Do not shake violently
● Peak hold and track mode selectable or drop wrench.
● Buzzer and LED indicator for the 9 pre-set 3. Do not use the wrench
target torques as a hammer.
● Water contact indicator 4. Do not leave the wrench in any place exposed to
● Engineering units (ft-lb, in-lb, N-m, kg-cm) excessive heat, humidity, or direct sunlight.
5. Do not use the wrench in water (not waterproof).
selectable 6. If the wrench gets wet, wipe it with a dry towel
● Stores up to 50 data files for recall and joint as soon as possible. The salt in seawater can be
torque auditing especially damaging.
● Auto Sleep after about five minutes idle 7. Do not use organic solvents, such as alcohol or
● (2) AAA Batteries included paint thinner when cleaning the wrench.
8. Keep the wrench away from magnets.
9. Do not expose the wrench to dust or sand as this
could cause serious damage.
10. Do not apply excessive force to the LCD panel.
11. Apply torque slowly and grasp the center of the
handle. Do not apply load to the end of the
handle.
BATTERY MAINTENANCE
1. When the wrench is not used for an extended
period of time, remove the battery.
2. Keep a spare battery on hand when going on a
long trip or to cold areas.
3. Do not mix battery types or combine used
batteries with new ones.
4. Sweat, oil and water can prevent a battery’s
terminal from making electrical contact.
To avoid this, wipe both terminals before
loading a battery.
5. Dispose of batteries in a designated disposal area.
Do not throw batteries into a fire.
2
NAMES AND FUNCTIONS OF PARTS
1 2 3 4 5
6 7 8 9 10
11 12
14 15
13
16 17 18
1. Head Insert 10. Anti-Slip Handle
2. Sensor Yoke 11. Jaw Adjuster
3. LCD Readout 12. Battery Cover
4. Communication Part 13. LED Indicator
5. UP/DOWN Button 14. Torque Value
6. Buzzer 15. Units (ft-lb, in-lb, N-m,
7. Power ON/CLEAR Button kg-cm)
8. Unit/Setting Button 16. Pre-Setting Number
9. Pre-setting Number 17. Peak/Track Mode
Selection Button 18. Water Indicator
Viewing Window 3
BEFORE USING THE WRENCH
SPECIFICATIONS BEFORE USING
BEFORE USING THE WRENCH
BATTERY INSTALLATION
BATTERY INSTALLATION
Model Max. Square Torque Length Remove the battery cover.
Torque Drive Measuring
No. (inches) Range Insert
Remove twothe
AAA batteries
battery cover.matching the
-/+ polarities
Insert two AAA of batteries
the battery to the battery
matching the
60648 62.7 ft. lb. 3/8 3.1-62.7 ft. lb. 10.6 in. compartment.
-/+ polarities of the battery to the battery
85 N-m 4.2~85 N-m 270 mm Replace the
compartment. battery cover and fasten it tightly
All Models according
Replace the tobattery
the following figures.
cover and fasten it tightly
according to the following figures.
Accuracy *1 CW：±2%
Cover
CCW：±3%
Cover
Data memory test 50
Pre-Sets 9
6LEDs Battery
Bright LED
(1 Red+5 Green) Battery
Operation Mode Peak hold/Track
Unit Selection ft-lb, in-lb (N-m, kg-cm)
Gear Teeth 52
Button 5 ATTENTION:
ATTENTION:
Battery AAA x 2 (included) When opening the battery cover of your wrench,
ATTENTION:
Operating Temperature 14οF ~ 140οF (-10℃ ~ 60℃)
you
Whencanopening
see a viewing window
the battery coverfor
ofthe water
your wrench,
contact
you can indicator. Through
see a viewing windowthisfor
viewing
the water
Storage Temperature 4οF ~ 158οF (-20℃ ~ 70℃) window, you can check if the wrench
contact indicator. Through this viewing is
damaged by water
window, you penetration
can check (the water
if the wrench is
Humidity Up to 90% non-condensing
contact
damagedindicator
by waterturns red). (the water
penetration
Drop Test 1m contact indicator turns red).
Vibration Test *2 10G
POWER ON AND RESETTING THE WRENCH
Environmental Test *3 Pass POWER ON AND RESETTING THE WRENCH
Environmental Test *4 Pass Press to power on the digital torque wrench.
Presscan press
You…
